rpi: updated firmware and patchset.

config/kernel/kernel.config.armv5tel-ipfire-rpi

@@ -1,6 +1,6 @@
 #
 # Automatically generated file; DO NOT EDIT.
-# Linux/arm 3.2.28 Kernel Configuration
+# Linux/arm 3.2.30 Kernel Configuration
 #
 CONFIG_ARM=y
 CONFIG_SYS_SUPPORTS_APM_EMULATION=y
@@ -17,10 +17,12 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_HARDIRQS_SW_RESEND=y
 CONFIG_GENERIC_IRQ_PROBE=y
 CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_ARCH_HAS_CPUFREQ=y
 CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
 CONFIG_GENERIC_HWEIGHT=y
 CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_FIQ=y
 CONFIG_VECTORS_BASE=0xffff0000
 CONFIG_ARM_PATCH_PHYS_VIRT=y
 CONFIG_NEED_MACH_MEMORY_H=y
@@ -371,6 +373,29 @@ CONFIG_CMDLINE_FROM_BOOTLOADER=y
 #
 # CPU Power Management
 #
+
+#
+# CPU Frequency scaling
+#
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_TABLE=y
+CONFIG_CPU_FREQ_STAT=m
+# CONFIG_CPU_FREQ_STAT_DETAILS is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
+CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_POWERSAVE=m
+CONFIG_CPU_FREQ_GOV_USERSPACE=m
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
+
+#
+# ARM CPU frequency scaling drivers
+#
+CONFIG_ARM_BCM2835_CPUFREQ=y
 CONFIG_CPU_IDLE=y
 CONFIG_CPU_IDLE_GOV_LADDER=y
 CONFIG_CPU_IDLE_GOV_MENU=y
@@ -1469,9 +1494,6 @@ CONFIG_RT2X00_LIB_FIRMWARE=y
 CONFIG_RT2X00_LIB_CRYPTO=y
 CONFIG_RT2X00_LIB_LEDS=y
 # CONFIG_RT2X00_DEBUG is not set
-CONFIG_RTL8192CU=m
-CONFIG_RTLWIFI=m
-CONFIG_RTL8192C_COMMON=m
 CONFIG_WL1251=m
 # CONFIG_WL1251_SPI is not set
 CONFIG_WL1251_SDIO=m
@@ -1485,6 +1507,7 @@ CONFIG_ZD1211RW=m
 # CONFIG_ZD1211RW_DEBUG is not set
 CONFIG_MWIFIEX=m
 CONFIG_MWIFIEX_SDIO=m
+CONFIG_RTL8192CU=m
 
 #
 # Enable WiMAX (Networking options) to see the WiMAX drivers
@@ -1777,7 +1800,7 @@ CONFIG_W1_SLAVE_DS2760=m
 CONFIG_W1_SLAVE_DS2780=m
 CONFIG_W1_SLAVE_BQ27000=m
 # CONFIG_POWER_SUPPLY is not set
-CONFIG_HWMON=m
+CONFIG_HWMON=y
 CONFIG_HWMON_VID=m
 # CONFIG_HWMON_DEBUG_CHIP is not set
 
@@ -1885,8 +1908,9 @@ CONFIG_SENSORS_W83L785TS=m
 CONFIG_SENSORS_W83L786NG=m
 CONFIG_SENSORS_W83627HF=m
 CONFIG_SENSORS_W83627EHF=m
-CONFIG_THERMAL=m
+CONFIG_THERMAL=y
 CONFIG_THERMAL_HWMON=y
+CONFIG_THERMAL_BCM2835=y
 CONFIG_WATCHDOG=y
 # CONFIG_WATCHDOG_CORE is not set
 # CONFIG_WATCHDOG_NOWAYOUT is not set

config/rootfiles/common/armv5tel/rpi-firmware

@@ -5,6 +5,7 @@ boot/arm224_start.elf
 boot/arm240_start.elf
 boot/bootcode.bin
 boot/cmdline.txt
+boot/config.txt
 #boot/first32k.bin
 boot/loader.bin
 boot/start.elf

config/rpi-firmware/config.txt

@@ -0,0 +1,28 @@
+###############################################################################
+#
+# Raspberry Pi - Videocore configuration file
+#
+###############################################################################
+
+###############################################################################
+#
+# Turbo Mode (cpufreq) Settings ...
+# default clocks are arm=700, core=250 and sdram=400
+#
+###############################################################################
+#
+# underclock at idle
+arm_freq_min=500
+sdram_freq_min=250
+#
+# use following paramters to overclock at load
+#arm_freq=1000
+#core_freq=450
+#sdram_freq=450
+#over_voltage=2
+
+################################################################################
+#
+# end
+#
+################################################################################